Product ID: LCR-200 Precision LCR Instrument

FEATURES:

·         Measurement Parameters :

·         Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and θ.

·         Test conditions :

·         100MHz , 120Hz , 1KHz , 10KHz , 100KHz , 200KHz

·         Basic Accuracy 0.1% ;

·         Test Voltage:

·         1Vrms , 250mVrms , 50mVrms , 1Vdc(DCR only)

·         DMM Functionalities

·         Dual LCD Display with LED backlit

·         Open/Short Calibration

·         Remote Binning capacity

·         Auto range/ Range hold selection

·         RS-232 Interface

SPECIFICATIONS    
Test  Condition :
Frequency  : 100Hz/120Hz/1KHz/10KHz/100KHz/200KHz
Level           :  1V rms/250mVrms/50mVrms/1Vdc(DCR only)
Measurement Parameters  :    Z , Ls , Lp , Cs , Cp , DCR , ESR , D , Q , and θ.
Basic Accuracy :   0.1%

PRIMARY PARAMETERS DISPLAY
Z AC Impedance
DCR DC Resistance
Ls Serial Inductance
Lp Parallel Inductance
Cs Serial Capacitance
Cp  Parallel Capacitance

SECONDARY PARAMETERS DISPLAY
θ  Angle Impedance  
ESR Equivalent Series Resistance
D Dissipation Factor
Q Quality Factor
COMBINATIONS OF Display
Serial Mode Z-θ, Cs-D, Cs-Q, Cs-ESR, Ls-D, Ls-Q, Ls-ESR
Parallel Mode Cp-D, Cp-Q, Lp-D, Lp-Q

MEASUREMENT RANGE
Parameter Range
z 0.000 Ohm to 500.0 Ohm
L 0.030 uH to 9999 H
C 0.003 uH to 9999 H
DCR 0.000 Ohm to 500.0 M Ohm
ESR 0.000 Ohm to 9999 Ohm
D 0.000 to 9999
Q 0.000 to 9999
θ -180.0 degree to 180 degree
V 0.000mV to +/- 600.0V
ESR 0.000 Ohm to 9999 Ohm
D 0.000 to 9999
Q 0.000 to 9999
θ -180.0 degree to 180 degree
V 0.000mV to +/- 600.0V
I 0.000mA to +/- 2.000A

DC VOLTAGE MEASUREMENT
Range 2V, 20V, 200V and 600V
Resolution 1mV, 10mV, 100mV, 1V
Accuracy +/- (0.4% +3 digits)
input Impedance 1 M Ohm
AC CURRENT MEASUREMENT
Range 2A, 0.2A, 20mA and 2mA
Resolution 1mA, 10mA, 100mA, 1A
Accuracy +/-(0.8% +5 digits) @ 40 Hz ~ 1 kHz
Input Impedance 1M ohm
AC CURRENT MEASUREMENT ( True RMS)
Range 2A, 0.2A, 20mA and 2mA
Resolution 1mA, 10mA, 100mA, 1A
Accuracy +/-(0.8% +5 digits) @ 40 Hz ~ 1 kHz
Current Shunt 0.1 Ohm@ current > 20mA/ 10 Ohm@ current </= 20mA
CONTINUITY CHECK
Continuity Thresh hold 50 Ohm (Approximately)
Continuity Indicator Tone Buzzer
Input Protection 600 Ohm (max)
DIODE TEST MEASUREMENT
Test Current 2.5mA ( Typical)
Open Circuit Voltage 5.0V DC (NOMINAL)
Input Protection 600V (max)
DIODE TEST MEASUREMENT
Power source AC 110/ 220V +/- 10% ; 50 / 60 Hz  
Operating Temp  0 to 40 ‘C (Operating) ; < 85 % RH
Storage Temp -20 ‘C to 70 ‘C
GENERAL
Dimensions: 300 mm x 220 mm x 150 mm ( 11.8" x 8.7" x 5.9 ") (Dx W x H)
Weight 4.5kgs
Standard Accessories  (1). TL09C Kelvin Clips x 1 pc (2) Test Leads x 1 pc     Power Cord x 1;  
Instruction Manual x 1
Optional Accessories   (3) TL09A SMD test Probe ( 4) TL 09B Component Fixture

Certificate: CE
Ordering information:
LCR-200 LCR precision Instrument